Add all relevant information to the CHANGES file. Fix the leading case
of some entries for consistency, and remove one which wasn't worth
mentioning.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
For all manpages installed on my Debian system, add a BUGS section, so
people can easily find whom to contact.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Sometimes I need to add some flags (like -static for the linker), so
allow this for all CFLAGS and LDFLAGS used in this project.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Jean Delvare <jdelvare@suse.de>
The I2C standard reserves addresses 0x03-0x07. Adapt our tools to that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The text describing the address to be used did not reflect the recent
change where some of the functionality of '-f' has been seperated into
'-a'.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There was a last instance of sprintf which somehow was not converted.
I know it can't fail, but for consistency, let's use snprintf and
check for truncation as we already do in gather_i2c_busses().
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Add all the JEDEC-registered manufacturer names added since JEP106AQ.
Signed-off-by: Vincent Palatin <vpalatin@upmem.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
The Python bindings haven't been updated after commit
330bba29f3 ("libi2c: Properly
propagate real error codes on read errors"). This led to erronenous
behavior every time an error other than -1 is returned by i2c_smbus_*
functions.
[JD: Edited description.]
Signed-off-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Increese sleep time between writes to accomodate typical write
cycle times. An Atmel AT24C02 as well as an ON Semiconductor
CAT24C02 EEPROM specify 5ms. This resolves errors such as:
...
Bus: /dev/i2c-1, Address: 0x50, Mode: 8bit
Writing stdin starting at address 0x0
..Error i2c_write_2b: Input/output error
Error at line 162: write error
[JD] Define a single constant and add a note that this could be
revisited.
Based on a patch from Peter Missel. The meaning of byte 31, bit 1,
was inverted. Also, this bit is only meaningful if the extended
temperature range is supported (bit 0 is set.)
git-svn-id: http://lm-sensors.org/svn/i2c-tools/trunk@6249 7894878c-1315-0410-8ee3-d5d059ff63e0
When you do `pydoc smbus`, you just get the high level description.
There is no automatic display of the classes (like SMBus). This is
due to the name not being specified quite right in the type.
Contributed by Mike Frysinger.
git-svn-id: http://lm-sensors.org/svn/i2c-tools/trunk@6171 7894878c-1315-0410-8ee3-d5d059ff63e0
Jean Delvare
Wolfram Sang
Wolfram Sang
Vincent Palatin
Georgii Staroselskii
Wolfram Sang
Stefan Agner